tag:blogger.com,1999:blog-8515829.post1997251388601602013..comments2024-03-28T00:27:14.676-07:00Comments on Irons in the Fire: Anybody changed a bathtub faucet spout?Firehandhttp://www.blogger.com/profile/04562365951182027709noreply@blogger.comBlogger6125tag:blogger.com,1999:blog-8515829.post-476996153675884412014-05-23T17:50:34.024-07:002014-05-23T17:50:34.024-07:00Good advice all 'round, thanks.
Not a rush ma...Good advice all 'round, thanks.<br /><br />Not a rush matter; long as I can run water to bathe with, I'm good. If it won't loosen up with a big of wiggling, I'll go the dremel route.Firehandhttps://www.blogger.com/profile/04562365951182027709noreply@blogger.comtag:blogger.com,1999:blog-8515829.post-52351729751018125862014-05-23T17:45:02.801-07:002014-05-23T17:45:02.801-07:00PB Blaster will work well also.....But,,,,I would ...PB Blaster will work well also.....But,,,,I would be real careful especially on a Holiday weekend.....A plumber can be really expensive during that time....<br />Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-8515829.post-25057976742744880922014-05-23T16:03:05.486-07:002014-05-23T16:03:05.486-07:00If you can't place a backup wrench on the pipe...If you can't place a backup wrench on the pipe in the wall, don't get too rough with trying to remove the spout. <br /><br />If you have a dremel tool, whittle away at the spout a little at a time, until you expose the part where it't threaded. Cut that part just to the top of the threads and you'll eventually have enough removed to place a little pressure, which will complete the cut and allow the expanded female threads of the spout to release from the nipple protruding through the wall. <br /><br />It's time consuming, but beats hell out of tearing out a wall. Jesshttps://www.blogger.com/profile/15969361446367636746noreply@blogger.comtag:blogger.com,1999:blog-8515829.post-47056081154925365782014-05-23T14:31:37.368-07:002014-05-23T14:31:37.368-07:00They're usually a screw in on anything made in...They're usually a screw in on anything made in the last few decades. But. The problem is corrosion. They can get to the point that the dis-similar metals (chrome steel and copper usually) can become almost welded together. What you're chancing is twisting off the copper pipe behind the wall. If that happens it's tear out the wall time. If it's bad try some WD40 up the spout with plenty of time to penetrate and work it back and forth to try and get it to loosen. I gotta warn you that if it's gotten too bad it almost certainly won't work. If you must then you must. If it's not an immediate issue you may be better served leaving it alone until it's time for a bathroom redo. Then you can tear it all out and start from scratch. <br /><br />Sorry Firehand. There's just no easy solution. Sixhttps://www.blogger.com/profile/05572583408046642437noreply@blogger.comtag:blogger.com,1999:blog-8515829.post-69368755188735085432014-05-23T14:27:59.875-07:002014-05-23T14:27:59.875-07:00Ditto. Check for a set screw, if there isn't ...Ditto. Check for a set screw, if there isn't one, twist away.Phelpshttps://www.blogger.com/profile/06270536870200063563noreply@blogger.comtag:blogger.com,1999:blog-8515829.post-48753256151254107342014-05-23T14:00:44.913-07:002014-05-23T14:00:44.913-07:00How old?
For several decades, bathtub spouts have ...How old?<br />For several decades, bathtub spouts have consisted of a stub of copper pipe sticking out of the wall, and then the pretty chrome bit just slides on, and is likely held in place with a set screw.<br /><br />If it's more than a few decades old, you need someone smarter than me.Anonymousnoreply@blogger.com